Mylee Pre Care Gel - 500ml

This pre-waxing cleanser is a must before any depilatory treatment. Deeply cleansing, it removes oil, impurities and makeup from your skin to prepare it for waxing or other hair removal treatments and achieve the best possible results.

This pre-waxing cleanser also contains aloe vera, renowned for its soothing and healing properties. So not only will your skin be hair-free, but it’ll be soft and silky smooth too!

• Deep cleans
• Removes oil, impurities and makeup
• Prepares skin for waxing
• Formula contains aloe vera

To use, apply pre-waxing cleanser to a cotton pad or lint-free wipe and gently sweep away impurities, then allow to dry. Your skin is now fresh, clean and ready for depilatory treatment.

This product works perfectly with Mylee After Care Lotion and Mylee Assorted Spatulas. 

STEP 1. HEAT
Place your Mylee Advanced Professional Stripless Wax into the Mylee Digital Wax Heater* using the Mylee Silicone Jar*. Allow the beads to melt to a smooth, even consistency. Always test the temperature on the inside of your wrist - it should feel warm, never hot.

STEP 2. PREP
Ensure the skin is clean, dry and free from any oil, makeup or impurities before waxing. Apply a thin layer of Mylee Pre & Post Wax Oil* using a cotton pad* or clean hands to create a protective barrier, helping the wax grip hair, not skin.

STEP 3. APPLY
Using a Mylee Disposable Spatula*, spread a layer of wax evenly in the direction of hair growth. Allow the wax to cool and harden. Hold the skin taut and remove the wax in one firm motion against the direction of hair growth. Repeat as needed until the area is smooth.

STEP 4. FINISH & CARE
Apply Mylee Pre & Post Wax Oil* to remove any wax residue and help nourish the skin. 

*Products sold separately.

Mastering the Mylee Advanced Stripless Wax is all about that "cool and pull" technique.

• Getting the temp right is everything. You want your wax to look like thick, gooey honey - not runny water!
  Melt your wax using a high heat for about 15-20 minutes, then turn the dial down to medium. Our Digital wax Heater does this for you automatically! If the wax runs off your spatula instantly, it’s too hot. Let it sit for a minute until it stays on the stick for a few seconds when you twirl it.

• When you apply your wax in a strip, make sure the very end (where there is no hair) is a little bit thicker than the rest. This creates a "pull tab" or lip. It means you can get a firm grip and flick it back without having to pick at the edge.
  
• Don't be shy with that spatula! If you apply the wax too lightly, it won't "shrink-wrap" the hair.
  
• Use firm, even pressure when spreading the wax in the direction of hair growth. You want to really push the wax into the hair follicles so it grabs every single strand from the root.
  
• Hold the skin as taut as possible. When you pull the wax off, keep your hand parallel and close to the skin, pulling back in the opposite direction of growth. Think of it as a "flick" rather than a "lift" - it’s faster, smoother, and way less "ouchy."
  
• As soon as you’ve pulled the wax strip off, immediately press your palm firmly onto the skin for a few seconds. The pressure confuses your nerves and stops the "sting" before it even starts. Total game-changer!
  
• Use the Mylee Silicone Bucket for your beads. Once you’re finished and the wax has cooled completely, just "pop" the hardened wax disc out. You can save it for your next session or wipe the bucket clean in seconds. No mess, no stress.

Aqua (Water), Alcohol Denat., Carbomer, Triethanolamine, Aloe Barbadensis Leaf Juice, Menthol, Parfum (Fragrance), Terpineol, Citronellol, Alpha-Isomethyl Ionone, Citric Acid, Potassium Sorbate, CI 18050 (Red 1).